|
| | Modbus ()=default |
| |
| void | setup () override |
| |
| void | loop () override |
| |
| void | dump_config () override |
| |
| void | register_device (ModbusDevice *device) |
| |
| float | get_setup_priority () const override |
| |
| void | send (uint8_t address, uint8_t function_code, uint16_t start_address, uint16_t number_of_entities, uint8_t payload_len=0, const uint8_t *payload=nullptr) |
| |
| void | send_raw (const std::vector< uint8_t > &payload) |
| |
| void | set_flow_control_pin (GPIOPin *flow_control_pin) |
| |
| void | set_send_wait_time (uint16_t time_in_ms) |
| |
| void | set_disable_crc (bool disable_crc) |
| |
| | UARTDevice ()=default |
| |
| | UARTDevice (UARTComponent *parent) |
| |
| void | set_uart_parent (UARTComponent *parent) |
| |
| void | write_byte (uint8_t data) |
| |
| void | write_array (const uint8_t *data, size_t len) |
| |
| void | write_array (const std::vector< uint8_t > &data) |
| |
| template<size_t N> |
| void | write_array (const std::array< uint8_t, N > &data) |
| |
| void | write_str (const char *str) |
| |
| bool | read_byte (uint8_t *data) |
| |
| bool | peek_byte (uint8_t *data) |
| |
| bool | read_array (uint8_t *data, size_t len) |
| |
| template<size_t N> |
| optional< std::array< uint8_t, N > > | read_array () |
| |
| int | available () |
| |
| void | flush () |
| |
| int | read () |
| |
| size_t | write (uint8_t data) |
| |
| int | peek () |
| |
| void | check_uart_settings (uint32_t baud_rate, uint8_t stop_bits=1, UARTParityOptions parity=UART_CONFIG_PARITY_NONE, uint8_t data_bits=8) |
| | Check that the configuration of the UART bus matches the provided values and otherwise print a warning. More...
|
| |
| float | get_actual_setup_priority () const |
| |
| void | set_setup_priority (float priority) |
| |
| virtual float | get_loop_priority () const |
| | priority of loop(). More...
|
| |
| void | call () |
| |
| virtual void | on_shutdown () |
| |
| virtual void | on_safe_shutdown () |
| |
| uint32_t | get_component_state () const |
| |
| virtual void | mark_failed () |
| | Mark this component as failed. More...
|
| |
| bool | is_failed () |
| |
| bool | is_ready () |
| |
| virtual bool | can_proceed () |
| |
| bool | status_has_warning () const |
| |
| bool | status_has_error () const |
| |
| void | status_set_warning (const char *message="unspecified") |
| |
| void | status_set_error (const char *message="unspecified") |
| |
| void | status_clear_warning () |
| |
| void | status_clear_error () |
| |
| void | status_momentary_warning (const std::string &name, uint32_t length=5000) |
| |
| void | status_momentary_error (const std::string &name, uint32_t length=5000) |
| |
| bool | has_overridden_loop () const |
| |
| void | set_component_source (const char *source) |
| | Set where this component was loaded from for some debug messages. More...
|
| |
| const char * | get_component_source () const |
| | Get the integration where this component was declared as a string. More...
|
| |
|
| bool | parse_modbus_byte_ (uint8_t byte) |
| |
| virtual void | call_loop () |
| |
| virtual void | call_setup () |
| |
| virtual void | call_dump_config () |
| |
| void | set_interval (const std::string &name, uint32_t interval, std::function< void()> &&f) |
| | Set an interval function with a unique name. More...
|
| |
| void | set_interval (uint32_t interval, std::function< void()> &&f) |
| |
| bool | cancel_interval (const std::string &name) |
| | Cancel an interval function. More...
|
| |
| void | set_retry (const std::string &name, uint32_t initial_wait_time, uint8_t max_attempts, std::function< RetryResult(uint8_t)> &&f, float backoff_increase_factor=1.0f) |
| | Set an retry function with a unique name. More...
|
| |
| void | set_retry (uint32_t initial_wait_time, uint8_t max_attempts, std::function< RetryResult(uint8_t)> &&f, float backoff_increase_factor=1.0f) |
| |
| bool | cancel_retry (const std::string &name) |
| | Cancel a retry function. More...
|
| |
| void | set_timeout (const std::string &name, uint32_t timeout, std::function< void()> &&f) |
| | Set a timeout function with a unique name. More...
|
| |
| void | set_timeout (uint32_t timeout, std::function< void()> &&f) |
| |
| bool | cancel_timeout (const std::string &name) |
| | Cancel a timeout function. More...
|
| |
| void | defer (const std::string &name, std::function< void()> &&f) |
| | Defer a callback to the next loop() call. More...
|
| |
| void | defer (std::function< void()> &&f) |
| | Defer a callback to the next loop() call. More...
|
| |
| bool | cancel_defer (const std::string &name) |
| | Cancel a defer callback using the specified name, name must not be empty. More...
|
| |
Definition at line 13 of file modbus.h.
Public Member Functions inherited from esphome::uart::UARTDevice